13623283880 0318-4599898

PRODUCT
PRODUCT
PRODUCT
current location:首页 >> PRODUCT
1-1-2
release time:2019-10-10

  Nylon polyamide (PA for short), with a density of 1.16g/cm3, is a thermoplastic resin containing repeating amide group - [nhco] - on the main chain of the molecule, including aliphatic PA, aliphatic aromatic PA and aromatic PA. Among them, aliphatic PA has many varieties, large yield and wide application, and its name is determined by the specific number of carbon atoms in the synthetic monomer.
  
  Nylon products have a wide range of uses. It is a good material to replace steel, iron, copper and other metals with plastics. It is important to replace the wear-resistant parts of mechanical equipment with MC mold nylon, and copper and alloy as wear-resistant parts of equipment. Suitable for making wear-resistant parts, transmission structure parts, conveying sliding parts, automobile manufacturing parts, chemical machinery parts, chemical equipment and other parts. Such as gear wheel, roller caster, shaft sleeve, slide pulley, impeller, conveying idler, structural connector, sealing ring gasket, screw, nut, etc.
  
  1 high strength, able to bear load for a long time.
  
  Good resilience, can bend without deformation, can keep toughness and resist repeated impact.
  
  The wear-resistant and self-lubricating property provides better performance than that of bronze cast iron carbon steel and phenolic laminate in oil-free (or deoiling) lubrication application, reduces consumption and saves energy.
  
  The MC nylon modulus is much smaller than that of metal, and the attenuation of vibration is larger, which provides a practical way to prevent noise better than metal.
  
  Compared with metal, MC nylon has low hardness and does not damage the wear parts.
  
  6. The continuous withstand working temperature is - 40 ~ 100 ℃
  
  I: Nylon 6
  
  Outstanding toughness, temperature resistance - 40-110 degrees, excellent wear resistance, slightly poor dimensional stability, moderate price, mostly used for one-time injection molding.
  
  II. Nylon 66
  
  Toughness and strength are outstanding, temperature resistance - 50-130 degrees, excellent wear resistance, general dimensional stability, high price, mostly used for one-time injection molding
  
  III. MC nylon
  
  Toughness and strength are outstanding, temperature resistance - 40-110 degrees, excellent wear resistance, general dimensional stability, moderate price, products are mostly machined from rods, tubes, and plate profiles, the product can be a few grams to hundreds of kilograms.
  
  Four: change the name to nylon
  
  1 glass fiber reinforced nylon: increase in strength, decrease in toughness and increase in temperature resistance.
  
  2 carbon fiber reinforced nylon: strength increased to the limit of nylon, toughness slightly lower, temperature resistance increased to the limit of nylon.
  
  3 molybdenum disulfide self-lubricating wear-resistant nylon: reduce the friction coefficient and improve the wear resistance of the product.
  
  4 oil contained self-lubricating wear-resistant nylon: reduce the friction coefficient and improve the wear resistance of the product.
  
  5. Low temperature resistant toughening nylon: increase the toughening agent in proportion to improve the toughness of the product, resulting in no embrittlement under low temperature environment.
  
  6 high temperature resistant nylon: the maximum service temperature can reach 260 ℃。

return
1-1-2
release time:2019/10/10

  Nylon polyamide (PA for short), with a density of 1.16g/cm3, is a thermoplastic resin containing repeating amide group - [nhco] - on the main chain of the molecule, including aliphatic PA, aliphatic aromatic PA and aromatic PA. Among them, aliphatic PA has many varieties, large yield and wide application, and its name is determined by the specific number of carbon atoms in the synthetic monomer.
  
  Nylon products have a wide range of uses. It is a good material to replace steel, iron, copper and other metals with plastics. It is important to replace the wear-resistant parts of mechanical equipment with MC mold nylon, and copper and alloy as wear-resistant parts of equipment. Suitable for making wear-resistant parts, transmission structure parts, conveying sliding parts, automobile manufacturing parts, chemical machinery parts, chemical equipment and other parts. Such as gear wheel, roller caster, shaft sleeve, slide pulley, impeller, conveying idler, structural connector, sealing ring gasket, screw, nut, etc.
  
  1 high strength, able to bear load for a long time.
  
  Good resilience, can bend without deformation, can keep toughness and resist repeated impact.
  
  The wear-resistant and self-lubricating property provides better performance than that of bronze cast iron carbon steel and phenolic laminate in oil-free (or deoiling) lubrication application, reduces consumption and saves energy.
  
  The MC nylon modulus is much smaller than that of metal, and the attenuation of vibration is larger, which provides a practical way to prevent noise better than metal.
  
  Compared with metal, MC nylon has low hardness and does not damage the wear parts.
  
  6. The continuous withstand working temperature is - 40 ~ 100 ℃
  
  I: Nylon 6
  
  Outstanding toughness, temperature resistance - 40-110 degrees, excellent wear resistance, slightly poor dimensional stability, moderate price, mostly used for one-time injection molding.
  
  II. Nylon 66
  
  Toughness and strength are outstanding, temperature resistance - 50-130 degrees, excellent wear resistance, general dimensional stability, high price, mostly used for one-time injection molding
  
  III. MC nylon
  
  Toughness and strength are outstanding, temperature resistance - 40-110 degrees, excellent wear resistance, general dimensional stability, moderate price, products are mostly machined from rods, tubes, and plate profiles, the product can be a few grams to hundreds of kilograms.
  
  Four: change the name to nylon
  
  1 glass fiber reinforced nylon: increase in strength, decrease in toughness and increase in temperature resistance.
  
  2 carbon fiber reinforced nylon: strength increased to the limit of nylon, toughness slightly lower, temperature resistance increased to the limit of nylon.
  
  3 molybdenum disulfide self-lubricating wear-resistant nylon: reduce the friction coefficient and improve the wear resistance of the product.
  
  4 oil contained self-lubricating wear-resistant nylon: reduce the friction coefficient and improve the wear resistance of the product.
  
  5. Low temperature resistant toughening nylon: increase the toughening agent in proportion to improve the toughness of the product, resulting in no embrittlement under low temperature environment.
  
  6 high temperature resistant nylon: the maximum service temperature can reach 260 ℃。

1-1-2
release time:2019/10/10

  Nylon polyamide (PA for short), with a density of 1.16g/cm3, is a thermoplastic resin containing repeating amide group - [nhco] - on the main chain of the molecule, including aliphatic PA, aliphatic aromatic PA and aromatic PA. Among them, aliphatic PA has many varieties, large yield and wide application, and its name is determined by the specific number of carbon atoms in the synthetic monomer.
  
  Nylon products have a wide range of uses. It is a good material to replace steel, iron, copper and other metals with plastics. It is important to replace the wear-resistant parts of mechanical equipment with MC mold nylon, and copper and alloy as wear-resistant parts of equipment. Suitable for making wear-resistant parts, transmission structure parts, conveying sliding parts, automobile manufacturing parts, chemical machinery parts, chemical equipment and other parts. Such as gear wheel, roller caster, shaft sleeve, slide pulley, impeller, conveying idler, structural connector, sealing ring gasket, screw, nut, etc.
  
  1 high strength, able to bear load for a long time.
  
  Good resilience, can bend without deformation, can keep toughness and resist repeated impact.
  
  The wear-resistant and self-lubricating property provides better performance than that of bronze cast iron carbon steel and phenolic laminate in oil-free (or deoiling) lubrication application, reduces consumption and saves energy.
  
  The MC nylon modulus is much smaller than that of metal, and the attenuation of vibration is larger, which provides a practical way to prevent noise better than metal.
  
  Compared with metal, MC nylon has low hardness and does not damage the wear parts.
  
  6. The continuous withstand working temperature is - 40 ~ 100 ℃
  
  I: Nylon 6
  
  Outstanding toughness, temperature resistance - 40-110 degrees, excellent wear resistance, slightly poor dimensional stability, moderate price, mostly used for one-time injection molding.
  
  II. Nylon 66
  
  Toughness and strength are outstanding, temperature resistance - 50-130 degrees, excellent wear resistance, general dimensional stability, high price, mostly used for one-time injection molding
  
  III. MC nylon
  
  Toughness and strength are outstanding, temperature resistance - 40-110 degrees, excellent wear resistance, general dimensional stability, moderate price, products are mostly machined from rods, tubes, and plate profiles, the product can be a few grams to hundreds of kilograms.
  
  Four: change the name to nylon
  
  1 glass fiber reinforced nylon: increase in strength, decrease in toughness and increase in temperature resistance.
  
  2 carbon fiber reinforced nylon: strength increased to the limit of nylon, toughness slightly lower, temperature resistance increased to the limit of nylon.
  
  3 molybdenum disulfide self-lubricating wear-resistant nylon: reduce the friction coefficient and improve the wear resistance of the product.
  
  4 oil contained self-lubricating wear-resistant nylon: reduce the friction coefficient and improve the wear resistance of the product.
  
  5. Low temperature resistant toughening nylon: increase the toughening agent in proportion to improve the toughness of the product, resulting in no embrittlement under low temperature environment.
  
  6 high temperature resistant nylon: the maximum service temperature can reach 260 ℃。